For the full SSSTS course, you prepare and deliver a toolbox talk lasting approximately five minutes. Choose one relevant issue, explain the action your audience needs to take and check that the message is understood. This guide gives you three original worked talks, a blank planning sheet and a rehearsal process.
The SSSTS refresher does not require delivery of this full-course toolbox talk. Its trainer review still includes mandatory exercises, including an interactive CDM scenario, and participation.
The templates, timings and fictional examples are independent learning aids, not official CITB assessment materials or a guaranteed marking scheme.
Choose a worked SSSTS toolbox talk
Read a complete example, compare the audience questions and use the blank plan to prepare your own talk.
In this guide
What you are preparing to do
A toolbox talk is a short briefing about a health-and-safety subject. On the SSSTS course, the communication task sits within the full-course trainer review alongside mandatory exercises and engagement throughout the course.
The full-course task is an approximately five-minute talk, with some flexibility. It focuses on relevant messages and clear delivery to the intended audience. Follow your trainer's actual instructions about the task, timing and permitted aids; this guide does not replace them.
The mandatory Toolbox talks publication can provide topic inspiration. You still need to understand the issue and explain it in your own words. Memorising somebody else's script may leave you unable to answer a simple follow-up question.
Keep the course type clear
Full-course learners should prepare this talk and participate in the other required activities. Refresher learners should follow their own trainer-review tasks, including the CDM scenario; that scenario is not the refresher's only mandatory activity. Read the current SSSTS assessment requirements for the wider assessment context.
Choose a manageable topic
Start with a decision the audience may face. “Construction safety” is too broad for a short talk. “What to do when the pedestrian route beside today's delivery area is blocked” gives the audience a particular situation and action.
Scroll sideways to compare all columns. Keyboard: focus the table and use the arrow keys.
| Narrow topic | Audience and decision | Keep the boundary clear |
|---|---|---|
| A blocked pedestrian route | People walking past a delivery area: report the obstruction and avoid improvising a diversion into vehicle movements. | The talk explains the agreed traffic arrangement; it does not authorise a new route. |
| Required dust extraction is unavailable | A team about to carry out a dusty task: pause the affected work and report that a planned control is missing. | Do not claim that a disposable mask automatically replaces extraction or prescribe equipment outside your competence. |
| A defect is found in access equipment | People preparing to use a ladder: recognise the defect, prevent its use and report it through the site arrangements. | Do not improvise a repair or turn a short talk into specialist equipment instruction. |
Check the technical content against the actual work arrangements and appropriate competent advice. These short examples do not provide a complete method of work.
Know who will listen
Write down who the talk is for and what they should do afterwards. An experienced delivery team may need the changed arrangements explained; a new visitor may need the route identified without unexplained site abbreviations. Use understandable language and a visual that works from the audience's position.
Try this sentence before choosing your title: “After this talk, this audience will know what to do when this situation occurs.” If you need several unrelated situations to finish it, narrow the topic.
Plan the talk with a reusable structure
Our suggested structure uses three main points and two audience questions. Those numbers are a planning aid, not CITB scoring criteria. Include the task, the reason it matters, the agreed controls, the action if something changes and the person or route for reporting concerns.
Ask a question that makes the listener explain a decision. “What would you do if that route were blocked?” reveals more than “Does everybody understand?” Keep the discussion relevant and understandable, and give workers a chance to raise concerns.
A blank talk-planning sheet
Use these boxes for rehearsal notes. Replace every site-specific detail with confirmed information before a real briefing. Copy your text into your own file before leaving this page; the template downloads contain blank forms and examples, not your typed entries.
Fill in your rehearsal plan
1. Set the scene
2. Shape your message
3. Plan the follow-up
Download the editable planning sheet, worked example and speaker-note card.
Turn the plan into speaker notes
Reduce the finished plan to prompts: today's situation → why it matters → three actions → two questions → reporting contact → recap. Keep the full plan for checking accuracy. Short prompts help you look at the audience and respond to what they say, instead of reading an essay at them.
An annotated example: a blocked pedestrian route
This fictional learning example concerns workers walking from a pedestrian entrance towards a welfare building beside a delivery area. The established pedestrian route is separated from vehicle movements. Materials have obstructed it. No alternative route is authorised in this example.
The aim is to explain the existing arrangement and the response to a failure, not to design a traffic system. Real sites should plan to avoid reversing where possible and keep pedestrians and vehicles separated. The practical guidance here is for Great Britain; Northern Ireland has separate legislation.
Blocked walkway: what happens next?
Follow the numbered points on this example site plan.
- Use the walkway
Keep to the separated pedestrian route between the entrance and welfare.
- Stop at the blockage
Stored materials obstruct the route. Do not squeeze past or improvise a diversion.
- Stay out of the vehicle area
The barrier separates the areas. Walking around it is not an authorised alternative.
Keep the affected movement paused until the route is restored or an alternative is assessed, authorised and communicated.
Diagram in words: the pedestrian entrance leads towards the welfare building within a separated pedestrian area. Stored materials obstruct that route. The adjacent vehicle area is not an authorised alternative. Prevent the affected unsafe movement, report the obstruction through the site arrangements and wait for the planned route to be restored or an alternative to be assessed and authorised.
The completed plan
- Audience and outcome
- Workers using this fictional entrance. They should identify the planned route, explain why the obstruction matters and describe what they would do next.
- Hazard and controls
- People could enter moving or reversing vehicles' operating space. Keep the planned separation, maintain a clear walkway and use the site's reporting and restart arrangements when it is obstructed.
- Reporting contact in this example
- Sam, the fictional delivery coordinator, is the first reporting contact. In a real talk, replace that name with the confirmed person's role and the actual contact method.
- Understanding check
- Ask a listener to trace the pedestrian route on the drawing, identify where they would stop using it and explain whom they would contact. No one enters a live vehicle area for the demonstration.
- Follow-up
- Confirm that the obstruction is resolved or an assessed alternative is authorised, then communicate the arrangement before affected movement resumes.
A five-minute rehearsal outline
The timings below are suggested rehearsal segments, not official sub-scores or fixed CITB time limits. Allow the audience time to answer rather than filling every second with your own words.
- 0:00–0:4040 seconds
Establish the situation
“This talk is for people walking from our pedestrian entrance to the welfare building. Materials are blocking the route shown here. The delivery area is beside it, so walking around the blockage could put you into vehicle movements.”
Why this helps: the audience knows which task and changed condition you mean.
- 0:40–2:301 min 50 sec
Explain three points
“First, use the planned pedestrian route and keep outside the vehicle area. Second, keep that route clear: do not leave materials on it. Third, if it is blocked, do not squeeze past or invent a diversion. Stop using the affected route and report it to Sam, our delivery coordinator in this exercise. The affected unsafe movement stays paused until the route is restored or an alternative is assessed and authorised.”
Why this helps: each point describes an action, and the final point explains what happens when the usual control fails.
- 2:30–4:151 min 45 sec
Ask and listen
“Using the drawing, what would you do if you reached this obstruction?”
Listen for stopping short of the problem, reporting it and avoiding the vehicle area. Then ask:
“What needs to be confirmed before people use the route again?”
Listen for a restored route or an assessed, authorised alternative that has been communicated.
Why this helps: the answers show the listener's decision. If someone suggests walking behind the vehicle, revisit the separation principle before continuing.
- 4:15–5:0045 seconds
Recap and close the loop
“Use the planned route, keep it clear and report a blockage instead of improvising. Sam will coordinate the response in this example. Is there anything about the route or reporting arrangement we have not made clear?”
Record an unanswered concern and say who will check it and how the answer will be shared.
Why this helps: the close repeats the action and gives uncertainty somewhere to go.
The talk does not make a learner a vehicle signaller. Only trained and authorised people should direct movements. High-visibility clothing, eye contact or a reversing alarm does not replace a planned safe arrangement. Revise the traffic-management principles if you cannot explain why the controls matter.
Change a vague reminder into a useful message
Before adapting this example, verify the actual route, control arrangements, audience, contact method and authority for restarting. Do not transfer the fictional coordinator or drawing into a real briefing as though they were site facts.
Worked example: dust controls before cutting starts
Audience: a block-cutting team and workers sharing its area. Outcome: they can explain why controlling dust at source, protecting nearby people and using the assessed cleaning method all matter. The following is an original rehearsal example for a fictional task; replace the work details with the arrangements you have checked.
Opening: make the risk understandable
“Today we are discussing the dust from cutting blocks. The risk is not limited to the person holding the tool. People working nearby and those cleaning afterwards can also breathe it. Some construction dust is fine enough to be difficult to see, and repeated exposure can damage health. A clear-looking room is not our test of whether the controls work.”
Speaker note: explain the exposure before listing equipment. Use the task's material information; do not claim that every dust has the same composition or health effect. Assess, control and review the exposure from the actual task.
Three points to explain
- Reduce the dust-producing work. “Our first question is whether the cut can be avoided by using the right-size material or changing preparation. Where cutting is required, use the method and controls agreed for this material and tool. Moving a dusty task outdoors does not automatically make exposure acceptable.”
- Check the whole control arrangement. “For this fictional task, the method specifies on-tool extraction. Check the intended arrangement before starting and report a missing connection, damaged hose or ineffective control. Keep other people out of the affected work area under the agreed arrangements. A mask does not fix an absent source control; any required respiratory protection has its own selection, fit and use requirements.”
- Include cleaning and changes. “Follow the assessed cleaning method. Dry sweeping can put settled dust back into the air. A different tool, material, work area or nearby trade can change the exposure, so get the arrangements reviewed rather than carrying on with yesterday's assumptions.”
Speaker note: point to the relevant task information or a safe photograph of the specified equipment. Do not run a tool to create a dust demonstration. Consider substances generated by the work, everyone who could be exposed, the controls needed and when those arrangements need reviewing.
Ask the audience, then compare the reasoning
“The extraction has not arrived, but everyone has a mask. Can this task start?”
Answer to listen for: the specified control is missing, so the affected cutting stays paused until it is provided and checked or an appropriate alternative is assessed. “Everyone has a mask” does not establish adequate control of the task or protection of other people.
“The cutting is finished. What still needs controlling?”
Answer to listen for: exposure during cleaning and handling dusty material, other workers using the area, and the condition of equipment for its next use. Completing the cut does not remove settled dust or finish the planned housekeeping.
Close with a specific check-back
“Before this task starts, show me which method we are using, the control we need and how you report a problem. If any of those is unclear, we resolve it before the cut. Afterwards, use the planned cleaning method.” Record a genuine question and its owner; for example, “Which cleaning equipment is specified for this area?” Keep it open until the answer has been checked and shared.
Rehearsal tip: allow the audience to explain both answers. If the talk is running long, shorten the scene-setting rather than reading out the answers yourself. Practise it aloud against your trainer's timing instructions.
Worked example: checking a stepladder before use
Audience: workers using stepladders for an already assessed task. Outcome: they can identify the pre-use checks, distinguish condition from suitability and explain what to do with a defect. Use an image or a safely positioned, unused example for the talk; nobody needs to climb it.
Opening: two different questions
“Before using this stepladder, we need to know that it is suitable for the planned work and that its condition is satisfactory. Those are different questions. A brand-new ladder can be the wrong equipment for a task. A suitable type can still have damaged feet, a loose step or a faulty locking mechanism.”
Speaker note: the task's equipment choice must already have been assessed. This short talk teaches recognition and reporting; it does not select a ladder for every job. Use the actual manufacturer's pre-use instructions and the site arrangements.
Three points to explain
- Check before use and after a relevant change. “The person using the equipment checks it at the beginning of the working day and after something happens that could affect it, such as a drop or moving it from dirty ground to a clean surface. An earlier inspection does not tell us what happened since.”
- Look at the parts people depend on. “Look for damaged side rails, missing or worn feet, loose or damaged steps, contamination, a damaged platform and locking parts that do not function correctly. Use the manufacturer's instructions for this model. A label showing an inspection date does not remove the need to notice a new defect.”
- Deal with the defect and the task separately. “If you find a defect, do not use the stepladder. Tell the person in charge and follow the site's arrangements to prevent its reuse. Do not make a temporary repair. If another item is proposed, its suitability and condition still need checking; availability alone is not a selection decision.”
Use a visual question
Use the close-up illustration below to ask the team what they can actually observe. “The anti-slip foot on this leg is missing” is a useful description. “It looks a bit unsafe” makes the follow-up less clear. Then ask what they would do before anyone uses the stepladder.
Scroll the illustration sideways on a small screen to read both comparisons. A text description follows it.
“The inspection label is current. Does that change the response to the missing foot?”
Answer to listen for: no. The visible defect is information about its condition now. Prevent use and report it. A dated inspection cannot make a missing component reappear.
“Can we borrow a longer ladder and finish the task?”
Answer to listen for: first check whether the proposed equipment and method suit the actual work. Changing the equipment can change access, stability and how the task is done. It is not enough to find something else that reaches the work.
Close and record the learning
“Show me what you would check before use, how you would describe a defect and who receives the report. Use the agreed equipment; report a change before improvising.” A useful rehearsal note might say: “The learner named the damaged foot but assumed the inspection label overrode it. We clarified the difference between a previous record and present condition; their second explanation identified both.”
Keep wider equipment-choice questions connected to the specific pre-use message, without trying to teach every access system in one short talk.
Practise the delivery
Rehearse aloud with a timer. Silent reading hides sentences that are difficult to say and gives a poor estimate of discussion time. If you run long, remove an unrelated point rather than rushing the final question. Test the diagram from the distance at which the audience will see it.
Ask a colleague to explain the main action afterwards without looking at your notes. Invite them to name one unclear part. If they remember the hazard but not what to do, simplify the action and reporting step. This is practice for supervisor safety conversations, not a performance judged by how many technical terms you use.
Blank rehearsal feedback
Scroll sideways to compare all columns. Keyboard: focus the table and use the arrow keys.
| Check | Observation to record | Change before the next rehearsal |
|---|---|---|
| Relevance | Could the listener identify the task and main action? ______ | ______ |
| Pace and audibility | Could they hear and follow the explanation? ______ | ______ |
| Visual clarity | Could they read the labels and explain the route? ______ | ______ |
| Participation | What did their answer reveal? ______ | ______ |
| Uncertainty and follow-up | Which question needs checking, and with whom? ______ | ______ |
Worked feedback: “The rehearsal took 6 minutes 10 seconds. The listener understood the blocked route but could not name the reporting contact. I will remove the unrelated parking example, state the contact earlier and ask the listener to explain the reporting step.” This uses an observation to change the talk; it does not claim an official timing failure.
Download the blank feedback and action-record sheets with worked examples.
Handle a question you cannot answer
Say what you need to check: “I cannot confirm that alternative route. I will ask the person responsible for the traffic arrangement before it is used.” Do not bluff a technical answer or invite someone to try an uncertain method. Record the question, identify the competent person and return with the answer.
If presenting, reading or another aspect of the task concerns you, tell the trainer or provider early. Ask what support can be arranged before the course starts. Do not assume an exemption, replacement task or particular adjustment.
Take the skill back to the site
An assessed talk is a communication exercise. An operational talk must fit the current work, local controls and people involved. It does not replace induction, competent training, supervision or a suitable method of work. A useful discussion cannot compensate for a missing barrier or a blocked route.
Use operational toolbox talk topics and templates for broader workplace briefing needs, site induction for new arrivals and a task-specific RAMS briefing for the agreed work method. Base each briefing on the local arrangements and give information in a way the workforce understands.
Keep attendance, understanding and action separate
A name or signature can record attendance; it does not, by itself, prove understanding or competence. Record what you checked and what needs to happen next. Do not mark an unresolved concern as closed because the talk has ended.
- Worked attendance entry
- Fictional practice group: three learners attended the route briefing. Keep actual attendance details under your organisation's arrangements.
- Worked understanding check
- Each learner identified the blocked route on the drawing. One initially proposed using the vehicle area; the group revisited the control and that learner then explained the reporting action correctly.
- Worked action record
- Confirm the real reporting contact before using an adapted talk on site. Owner: the person preparing the talk. Due: before delivery. Status: open until the site's responsible person confirms the arrangement; record the confirmation and update the notes.
Use the SSSTS revision guide to strengthen the principles behind your topic, then practise with original SSSTS questions for broader revision. A mock result and a rehearsed presentation support learning; neither replaces the assessed course activities.
Common SSSTS toolbox-talk questions
How long should my SSSTS toolbox talk be?
For full SSSTS, prepare a talk of approximately five minutes, with some flexibility. Follow your trainer's instructions. The suggested segments in our worked outline are rehearsal guidance, not official sub-scores or a universal timing rule for workplace talks.
What topic should I choose?
Choose one relevant situation and the action the audience should take. A blocked pedestrian route, missing planned dust extraction or defective access equipment can give you a manageable starting point. Confirm the controls and stay within your understanding; no topic guarantees a pass.
Can I use a prepared toolbox-talk template?
A template can help you organise and adapt your own explanation. Follow the trainer's requirements and check every site-specific detail. Do not treat an online script as an official answer or read someone else's wording without understanding why the controls are appropriate.
Does the SSSTS refresher require a toolbox talk?
The current SSSTS-R trainer review does not require delivering the full-course toolbox talk. It still requires mandatory exercises, including an interactive CDM scenario, and engagement and participation. Check the assessment guide and your trainer's instructions for the correct course requirements.
What if I am nervous about presenting?
Practise aloud with short prompts, time the talk and ask someone to explain the main action afterwards. Start with a clear opening sentence and a simple visual. Tell the provider early about any support need; do not assume an automatic exemption or replacement assessment.
Should I use slides?
Use an aid only if it helps the audience and fits the trainer's arrangements. One readable drawing may communicate more than several dense slides. Check that everyone can see the labels and that you can explain the message without reading every line from a screen.
How do I check that people understood?
Ask a listener to explain what they would do in a realistic situation or describe the route on a drawing. Listen for the required action and correct an unsafe interpretation. A general “understood?” question or an attendance signature alone does not show that the message was understood.
Where can I find general toolbox talk topics?
Choose subjects that fit the current work and workforce. Broader operational toolbox talk topics and templates serve everyday site briefings; this guide concentrates on preparing the SSSTS assessment talk.